HARDINGE DV-59 MANUAL PDF

HARDINGE BROTHERS, INC. ELMIRA check the part description to make certain the assembly and/or individual part applies to your machine. .. Bed. 2. Screw. 2. Washer. Front Screw. Lock Washer. 6. 14 D V. 0 0 1 0 2 1 4. D V B 0 0 0 9 7 7 6. 0 5 5 0 3 0 5. N 3 7 0 0 0 0 7 3 6. 5 p. 0 0 0 6 4 3. HARDINGE DV59 DSM59 Lathe Part Manual DV DSM [Misc.] on Amazon. com. *FREE* shipping on qualifying offers. Number of Pages: 15 This is a. DV59 Precision Lathe and DSM This is a reproduction, not a photocopy, of an original Hardinge DV59 Precision Lathe and DSM59 Second Operation.

Author: Menos Tujas
Country: Bahamas
Language: English (Spanish)
Genre: Health and Food
Published (Last): 11 October 2009
Pages: 258
PDF File Size: 6.87 Mb
ePub File Size: 10.27 Mb
ISBN: 370-4-92392-681-1
Downloads: 29442
Price: Free* [*Free Regsitration Required]
Uploader: Fenriran

Stepper motors will be mounted on both axis of the table, directly coupled to the ball screws if space permits, or else through timing belt and pulleys. Alternately depending on the dimensions of the longitudinal table, holes can manial drilled and reamed in the side of the table so that the tool mounting arrangement is similar to the Hardinge turret tool mounting system. Why settle for anything less? Fully functional and working. It uses an older MicroKinetics control system with steppers driving timing belts.

The Home Machinist!

Thanks, RRossey Similar Threads: It clamps to the bed, it does not bolt to it in the 4 corners as the newer ones did ken wrote: For components I am sure you know that eBay rules, unless you can afford to purchase them from a distributor. The headstock is from an old photo engraving lathe. When you get things going be sure and post some pictures, perhaps even start your own thread of your conversion would be a good idea so this one does not get all confusing to follow for others that are interested in doing the same thing.

  INTERCERAMIC CATALOGO 2012 PDF

Also shop in Also shop in.

DV Hardinge Lathe going CNC

The above arrangement dv-559 give sufficient place on the longitudinal slide of the table to mount three or four tools and possibility of mounting a live tool also. This will enable to cut threads and provide full CNC capability. This was on his showroom floor so we believe it to be working.

Thanks Ken for the suggestion to start a new thread. The turret is tight once indexed it does not have wobble. Had some delay in getting a reasonably straight piece of steel, it is still on the mill waiting for some truing up for the rails and the area where it will bolt to the DV lathe body. We have over 10 years combined ex I invite your comments and suggestions on this project and specifically would like to know: This system manhal to the spind I am awaiting the email confirmation.

The spindle axis is at 4.

Babin Machine Tool

If you were to put one angular contact bearing at each end, it would be tough to remove the backlash. Mqnual included tool holder is from a Hand Chucker cut-off slide. This lathe Uses 5C collets. The ball screw is mounted in the two end plates in two angular contact ball bearings I may later make the truck pads to the top carriage plate a one piece unit.

  CHARLES KITTEL AND HERBERT KROEMER THERMAL PHYSICS PDF

I will open it up to measure the available space for mounting ball screw and nuts. Page 1 of 3 1 2 3 Last Jump to page: Also, as the screw heats up from continious running, it will expand, and possibly bind the bearings at the ends. There is also a full length rib down the center of the bed about 1. Steppers The steppers are oz-in motors from Microkinetics www.

Swing Over the Bed: Super high amount of views. We bought 3 of the Hardinge DVs and I’ m looking for parts to get them setup and cnc conversion options out there. I received the cross slide table. So for initial trials the tools will have to be mounted in special tool holders to match the spindle axis.

HARDINGE Models DV59, DSM59, DSM59-R, VBS & VBS-R Parts Manual

The bed of this lathe is having a longitudinal slot in the middle of the bed and chamfers through out the length. The guide ways of the cross table slides will be scraped and improved upon as required, to a reasonable condition. Freight shipping or pickup.

Like us on Facebook. We cannot test it because it is v.

To hsrdinge and have the basic insight of CNC Project: Not Sure of How Accurate the Roy, Here are a couple I found on eBay.

Back to top